Bathroom Sink Leaking From Lift Rod? Quick Fixes!

If water leaks from the bathroom sink, the lift rod may be leaking. The lift rod is located at the bottom of the faucet and provides a connection for a hook-shaped pipe that leads to the shut-off valve that controls water flow. 

The leaking sink is very frustrating, but you don’t need to worry; in this article, I will share how you can replace the lift rod to stop the bathroom sink from leaking.

How To Replace Leaking Lift Rod

Once you have identified where your leaky pipe is coming from, you will be ready to make an inexpensive fix by replacing it. Follow these steps to replace your lift rod.

  1.  Pry off the rubber gasket that covers the hole where the lift rod fits into its hole. This will allow you to continue using your faucet while removing it from its hole.
  2.  Attach a towel or rag underneath the faucet as it may drip while removing and replacing the lift rod. 

A wrench can be used with a soft-faced hammer to remove the faucet assembly from its hole and then remove a couple of small easy-to-remove screws that hold it on top of the sink.

  1.  Pull the faucet up and turn it so you can see the rod and pull it from its holding, then drop the old one into place. Make sure that you have a new gasket ready to go where the old one was removed
  2.  Attach the faucet to its holding screws, ensure it is tightly attached, and slide the pulley onto your lift rod. Ensure that your towel is still underneath the sink so that any drips will be caught.
  3.  If there are small holes in your sink, attach a Teflon tape around them to keep them free of leaks during operation, and attach hose clamps if there are larger holes.
  4.  Turn your water back on, test that your leak is fixed, and repeat the process if necessary.

Bathroom Faucet Leaking from Center Hole

Bathroom sink leaking

If your bathroom faucet is leaking, it’s essential not to get the faucet wet. Moisture around the base of a leaky faucet will only cause more water damage if the leak is not fixed immediately. Make sure not to get any water on it, as it can damage the drywall. 

To begin with, turn off the water to the faucet. Once the water is off, look at the base of the faucet. You should see two or four nuts holding it to a flexible pipe or mounting plate. 

Most bathroom sink faucets can be removed by simply removing these nuts. However, if you aren’t sure how to do this, call for help.

You should also see the water inlet and the water outlet. They should be one or two inches above the faucets mounted in your sink. You should also see a vent hole on one end of the faucet and a washer on the other end. 

This is called a pop-up drain. While you can remove these parts, it is not recommended because they don’t permanently seal properly once removed. 

It could cause more damage to your sink if water leaks into it from the drain holes after being blocked from normally draining by these parts.

What is a Faucet Lift Rod

Faucet Lift Rod

There are many different types of faucets. However, they all have one common issue. That issue is that they need a lift rod.

The function of the lift rod is to allow the water to flow from the faucet to the spout without having any splash from sitting in stagnant water, which can happen if a person does not take their time when turning on and off the water. 

A simple way for a person to avoid this common problem would be by using better kitchen habits, such as taking care to pull up on or push down on handles when opening or closing them, respectively. One common issue is that the faucet handle will be left on when a person has turned off the water. 

This can cause a person to believe that the water is still on when it has already been turned off and is dripping due to poor faucet design or possibly poor maintenance practices. Residual water supply valves may also cause this issue.

How Much Water a Faucet Lift Rod Can Hold?

A faucet lift rod holds up to 2/3 inches of water and, therefore, can reduce or eliminate the spillage within a faucet when used. If a person turns on the faucet, the water will be directed to the spout until it drains into the sink basin or other container. 

The liquid drained from the faucet can then be seen as a clear stream of water exiting from the bathroom sink. Every homeowner needs to remember that a lift rod does not lift water. 

A lifting rod retrieves any water retained within a faucet by keeping it above ground level. Once this occurs, it allows more of an opportunity for drainage before running into a sink or other outlet.

It is important to note that a faucet lift rod is not designed to hold water but rather to give a person a better ability to handle hot or cold water properly. Therefore, a lifting rod will not put much of an added load on the handle and help reduce unnecessary spillage. 

Another benefit of using an under sink faucet lift rod is that it eases drainage that otherwise may become more difficult due to constant vibrations or other factors. Many people have considered a faucet mount pull-out sprayer as an alternative.

Final Verdict

Leaking lift rods are usually easy to replace, and you need essential tools to do so, but you need to know the type of lift rod you will replace. The process is usually similar if it is for a sink or faucet. 

Use a plumber wrench and soft hammer when replacing the parts. Else the ordinary wrench might bend or break the pipe and damage the drywall behind it. 

If you don’t have the right tools, it is better to call a plumber who can replace the faulty lift rod without mess. 

Related Posts:

How To Correct Slope in Bathroom Floor?

How to Fix a Gurgling Bathroom Sink?

How Unlock Bathroom Door Push Button Lock

Leave a Comment