How Many Ceiling Fans Are On A 15 Amp Circuit?

It’s not just as simple as it seems to figure out how many amps a ceiling fan uses. There are several factors to consider, including the type of ceiling fan, its configurations, speed, and other factors.

The smallest ceiling fans use only 0.34 amps, while the largest take 1.5 amperes. A 48″ ceiling fan amps are 0.63 amps, and that’s the most common ceiling fan size.

On the other hand, a ceiling fan draws about 120 watts per amp. Low settings draw less current, while higher settings draw more. So based on these numbers, we can run 4 to 5 ceiling fans on a 15 amp circuit.

Continue reading to learn more about how many amps a ceiling fan uses and other ceiling fan topics and facts.

How Many Ceiling Fans Can Be On A 15 Amp Circuit?

When running, the average ceiling fan consumes 75 watts of electricity. However, according to the code, a circuit with 15 amps can only use 80% of its breaker.

The peak power of a 15 amp circuit is around 1800 watts. Many people recommend using no more than 80% of that, which is 1440 watts.

If we assume that a 52-inch ceiling fan is transmitting 100 watts of electricity at maximum speed, One ceiling fan can transmit a total of 280 watts of electricity if there are three 60-watt bulbs attached to it.

Likewise, at 120 volts, a 15-ampere circuit breaker provides a total of 1800 watts (15 * 120 = 1800). So 1440 watts is 80 percent of 1800 watts.

Considering all of these factors, a 15 amp circuit can support approximately 4 to 5 ceiling fans. That is, presuming the circuit with the 15 amp circuit breaker has nothing else attached to it.

It is, however, only required when installing ceiling fans in a large establishment. Or else, a 15 amp circuit will be ineffective.

How Many Amps Does A Ceiling Fan Consumes? 

Ceiling Fan Size (in diameter)Amps
240.34 amps
300.40 amps
360.46 amps
420.54 amps
480.63 amps
540.74 amps
600.85 amps
661.00 amps
721.50 amps

A ceiling fan consumes between 0.5 and 1 amp on average. The type of fan, model and settings all influence the amp used. When a ceiling fan is turned up to its highest setting, it consumes about 0.6 amp. The fan draws somewhere around 0.4 and 0.25 amp on low and medium settings.

Ceiling fans use an average of 0.5 to 1 amp. The number is primarily determined by the fan’s setting, speed, and the model that you are considering. The majority of modern ceiling fans operate on very low amps, typically under 1 amp.

Furthermore, the fan’s power settings determine the number of amps used by a ceiling fan.

For example, if the fan is set to low, it will only consume about 0.25 amps. However, if the fan is set to a moderate speed, it will draw about 0.4 amps.

When the fan is set to the highest setting, it consumes about 0.6 amp.

Furthermore, the type of fan we are considering has a significant impact on the varying amperage count. Let’s see how many amps different types of ceiling fans consume:

Normal Ceiling Fan Amp Usage:

A typical ceiling fan consumes between 0.5 and 1 amp. The number is determined by the ceiling fan’s power and speed settings.

If you consider the speed settings of a typical ceiling fan that was built recently, the fan will use about 0.4 amp on low settings and only 0.6 amp on high settings.

Hunter Ceiling Fan Amp Consumption:

The type of construction primarily determines a hunter ceiling fan’s ampere utilization.

If you’re thinking about getting a hunter ceiling fan with a light kit, it’ll use about 2 amps. A ceiling fan without a light kit from Hunter, on the other hand, consumes about 3 amps.

52-Inch Ceiling Fan Amp Consumption:

For example, consider a 52-inch ceiling fan. Low settings will use approximately 0.17 amp, while high settings will use approximately 0.65 amp.

Large Ceiling Fan Amp Usage:

Most large ceiling fans built recently require between 0.5 amp and 1 amp of power.

What Maximum Load Can A 15 Amp Circuit With Ceiling Fans Handle?

So, let’s take a look at what a circuit might look like. Depending on the situation, a typical circuit could include a bedroom or two, outlets, and possibly even overhead lights. The electrician designed it when the house was built, but there are some areas of the house that use a little too much power, such as the bathrooms in the kitchen.

For example, If you have a hairdryer in a bathroom, you could use one that acts on it. It could be drawing 1100 watts from a 1440-watt 15 amp circuit when it’s on a high.

So it’s a lot if you have two bathrooms connected to the same circuit and more than one person using them. You’re using two hairdryers, possibly a hairdryer and a curling iron. You could be in a predicament. You’re using too much power, and the wires are getting hot.

And, as with the kitchen, it could be hazardous. So, for example, toaster ovens in the kitchen can consume over a thousand watts, and you should carefully plan your kitchen circuit. You don’t have too much equipment and things plugged in at once.

What Size Circuit Breaker Do I Need For A 15 Amp Ceiling Fan Circuit?

Circuit Breaker Need For A 15 Amp Ceiling Fan
Circuit Breaker Need For A 15 Amp Ceiling Fan

Picking the correct breaker for a ceiling fan circuit is important for appropriately installing it. As a result, you must keep a close eye on the breaker. Determine the size of the circuit break required for a ceiling fan.

You can put your ceiling fan on a shared circuit with several other appliances.

If you install a ceiling fan on a 15 amp breaker, it can easily share the circuit with other appliances like lights, ceiling fans, and more.

In fact, on a 15 amp circuit breaker, you can install 4 to 5 ceiling fans at once.

If there are no other appliances on that circuit and you only want to operate ceiling fans, you can even run 6 to 7 ceiling fans on that circuit.

You can also use a 20 amp breaker for the same purposes. It will be able to transport heavy-duty appliances with ease.

The 220-volt circuit breaker is used by heavy-duty appliances such as gas stoves, furnaces, and central air conditioning units. These breakers are not required for a ceiling fan. Ceiling fans, which fall under the category of lights and electrical outlets, require a 110-volt outlet.

Can I Hook Up A Ceiling Fan To A 15-Amp Circuit?

Yes, a ceiling fan can be installed on a 15 amp circuit. You can do this in conjunction with other appliances such as lights, fans, and so on.

It is important to note that a 15 amp circuit has a load capacity of 1800 watts. As a result, it is intended to work with heavily loaded appliances. You can easily connect multiple ceiling fans to the circuit.

Moreover, You must pay special attention to the wiring. Check that the wiring is grounded. And in this case, a 12 gauge wire is advantageous.

How Many Bulbs Can Pair Up With Ceiling Fans On A 15 Amp Circuit?

A 15 amp circuit should be able to power four ceiling fans without issue. For example, A 52-inch fan consumes between 90 and 100 watts at high speed when equipped with three 60-watt light bulbs.

That means each fan will consume approximately 280 watts. A 120-volt, a 15-ampere circuit can deliver 1880 watts. Four fans at 280 watts each account for roughly one-third of the total wattage that the 15 amp circuit can support. You can also easily run 3 to 4 60-watt bulbs with it.

Do Ceiling Fans Need Special Wiring?

No, Ceiling fans do not require any special wiring. The wiring system is similar to that of a standard light installation.

Because ceiling fans are heavier than most other electronic appliances in the home, it is natural to wonder if they require special wiring. That, however, would not be necessary.

You can simply use a standard 12-2 wire to wiring a ceiling fan. In addition, if you’re installing an adjustable switch, a 12-3 wire is ideal.

Furthermore, you can always use 14 gauge wire. It will be as effective as any other wiring system.

Some electricians recommend using heavier-duty 12-2 or 12-3 wires rated for 15 amp circuits.

Can I Use 14 Gauge Wire For A Ceiling Fan?

Yes, 14 gauge wire can be used for a ceiling fan. However, in order to meet the code for a modern wiring system, you must use the 14 gauge wire with the ground. A 14-inch gauge wire is sufficient to carry the electricity for a standard ceiling fan.

It’s even useful if you want to use it to power a large ceiling fan. Ceiling fans do not require any additional wiring. While a 12-2 wire is preferred, a 14 gauge wire can be used without issue for a ceiling fan.

Do Ceiling Fans Consume A Lot Of Energy?

For Ceiling fans, it is true that they consume a lot of electricity. However, it has been discovered that an average ceiling fan uses less electricity than an air conditioner. So you can continue to use a ceiling fan to keep your room cool.

Depending on the power settings and model type, a typical ceiling fan consumes between 15 and 90 watts of energy. It is important to note that you can leave your fan running for up to ten hours without fear of damaging the coils or the ceiling.

Frequently Asked Questions

How Many Outlets On A 20 Amp Circuit?

On a 20 amp circuit, there are 7 to 8 receptacle outlets.
Because each receptacle carries 1.5 amps of electricity, experts recommend that 80 percent of each circuit be used to avoid accidents. A 20 amp circuit, it turns out, should typically use 7 to 8 receptacles.

How Do Amps And Watts Compare?

Based on a 120V input voltage, one amp is equal to 120 watts, so 0.5 amps equal 60 watts. This method of measuring and comparing electricity is consistent at all times. If the voltage falls to 110 volts, one amp equals 0.54 amps, and so on.

Does A Ceiling Fan Need Its Own Circuit?

Ceiling Fans are commonly wired on the same circuit as other lights and outlets. A ceiling fan does not require a dedicated circuit due to its low amperage. The incoming power supply is linked to the switch that operates the ceiling fan.

What Is The Monthly Electricity Consumption Of A Ceiling Fan?

The average cost of running a medium-sized ceiling fan is $.003 per hour. So, if you have a medium-sized ceiling fan running 24 hours a day, you should expect to pay about $0.065 per day, $0.45 per week, and $1.94 per month to run it. That’s some low-cost cooling and airflow!

How Much Do Ceiling Fans Cost To Buy And Operate?

Ceiling fans can range in price from $50 to $300 for a fan with five blades and lighting fixtures. Running a ceiling fan is very cheap. It only costs about $.01 per hour to run.

Is it Possible To Have A Bathroom Fan And A Light On The Same Circuit?

In general, residential exhaust fans use very little power and should not interfere with the lighting. Many bathroom fans include lights that are intended to be wired to the same switch on the same circuit. They can also be wired to different switches separately.

What is the Maximum Number Of Light Switches That Can Be Linked Together?

There isn’t any limit to the number of lights that can be connected to a circuit. The load of the fixtures determines the number of lights that a circuit can accommodate. A conventional 15A circuit can support up to 1400W of lighting loads. A lighting load of 1400 Watts can support one 1400W fixture or fourteen 100W fixtures.
Ceiling Fans are commonly wired on the same circuit as other lights and outlets. A ceiling fan does not require a dedicated circuit due to its low amperage. A shared circuit is one that subdivides out and contains multiple devices that use the same electrical circuit.

Is it Possible To Connect A Bathroom Fan To An Existing Light?

While many house owners prefer to have the fan and existing light on separate switches, having them on the same switch can work just as well. You or your children will not forget to use the fan with a single switch while showering or bathing. Switch off the circuit breaker for the bathroom you’re going to work on.

How Many Amps Are Required For Bathroom Lighting?

At least two of these circuits must be provided. The outlets are powered by a 20-amp circuit, while a 15-amp circuit powers the lights. If there is a ventilation fan in the bathroom, it can use the lighting circuit, but the circuit must be upgraded to 20 amps.

Can A Single Switch Control Two Ceiling Fans?

Even for a novice, connecting two ceiling fans to the same branch circuit is a simple project. When joining two fans to the same circuit and controlling them with the same set of switches, simply attach the fans’ neutral, ground, and hot wires in parallel.

Final Thoughts

As you can see, ceiling fans need very small amount of electricity to keep you cool, only a few pennies per day. 

The amount of amps used by a ceiling fan is determined by several factors, including the type of ceiling fan, size, speed settings, and other factors. An average ceiling fan in a medium to high setting requires between 0.5 and 1 amp.

As a result, we concluded that a ceiling fan on a 15 amp circuit could power 4 to 5 ceiling fans. It should be noted that the amp used decreases as the speed decreases.

Related Posts:
How To Remove Plastic Ceiling Light Covers?

How To Clean Ceiling Fan Blades Without Ladder

Leave a Comment