How To Remove Ceiling Light Cover No Screws? (Easy Steps)

Ceiling light covers are made for human convenience. But because we all are so used to traditional things, removing the ceiling light cover without screws seems to be a difficult task.

Nowadays, ceiling light covers without screws are a part of every modern home and are easy to handle. There are specific steps to follow to get off the glass cover from the ceiling light in minutes.

Before moving on towards the step, follow all the safety measures like a sturdy and levelled stool, gloves, and switching off the power at the main circuit breaker switch.

Besides changing the light, you should remove the cover from time to time to clean it to make the whole room look nice.

Then finally, you can twist, bump and remove the glass cover from the ceiling light.

How To Remove A Ceiling Light Cover No screws

Remove A Ceiling Light Cover No screws
Remove A Ceiling Light Cover No screws

Most ceiling light covers are held in place with the help of spring clips. You can release the clip quickly by pushing it down on the cover while pulling it away from the light.

The removal process of the light cover may take some efforts and patience. Following are the steps to remove a ceiling light cover with no screws:

Components needed:

  1. Sturdy ladder or stool
  2. A pair of pliers
  3. Flashlight
  4. Gloves

1- Get a Sturdy Ladder Or Stool

Unless you’re very tall, you’ll need a ladder or stool to stand on and reach the ceiling light. Place the ladder as close to the wall as possible and ensure you place it on the levelled ground before standing on it.

You can use anything to reach the ceiling, for example, a sturdy chair or even a sofa. Then, turn off the power at the main circuit breaker switch.

Don’t miss this step at any cost, as it is crucial for your safety. Lastly, follow all the safety measures to be saved from an electric shock.

2- Wear Pair Of Gloves

To protect your hands and let them clean, you should wear gloves to remove the glass cover easily. You can use a mechanic or even gardening gloves for some extra traction. Gloves made with leather can be an excellent choice to protect your hands.

Wearing gloves is especially important for removing the ceiling cover because you need to rotate the light cover. Ensure that the gloves don’t have an open cuff design on the wrist.

3- Remove The Additional Decorations

If you have installed extra pieces or decorations at the base of your ceiling light, remove them first.

Trim pieces might be held to the ceiling in place by spring clips like no screw ceiling light cover.

4- Use Pliers For Removing The Spring Clip

Firstly grab a pair of long nose pliers to reach the hole around the base of your no screw ceiling light, and gently push down the spring clip to release it.

Here, you might need a flashlight to see whether your ceiling light has decorative trim around it to make the other processes easier for you.

5- Hold The Glass With Both Hands

Here you want to be super careful handling the glass cover. Because this type of glass cover has no knob, you need traction to rotate it. So put your hands on the opposite sides of the glass cover.

6- Rotate the glass left

Now that you have done all the preparations for removing the cover from the ceiling light, you need to take off the cover.

To do that, rotate the glass cover left or in a counterclockwise motion.

7- Lightly Bump With Shoe, If Stuck

Light covers get stuck, especially when they are untouched for years. Therefore, a great hack would be to lightly bump the cover with the rubber side of the shoe. It will loosen the light cover.

But be careful while doing it because you don’t want to break the glass.

8- Take Off The Glass Cover

Once the cover is loosened up and movable, gently and carefully lift away the glass cover off the ceiling. You may even need a pair of pliers to grip the glass cover. Now you can change the bulb or whatever you want to do.

9- Remove Bulb/Clean Dust

Once the removal process of the light cover is successfully done, you can change the bulb. It is also a great time to clean any dust or debris accumulated near your light.

Don’t touch the glass part of the new ceiling bulb for safety measures with your bare skin.

10- Replace The Glass Cover

Once you have replaced the old bulb with the new one, it’s time to replace the ceiling light cover. Reverse the steps discussed above to do it.

Make sure that the spring clips are correctly placed at the base of the light fixture, and keep pushing it down on the cover until it snaps into its place perfectly.

If there were any trim pieces or decorative pieces you previously removed, re-install them.

11- Turn The Power On To Test Light

Once everything is well assembled and sorted, go to the main circuit breaker switch from where you turned the power off previously; now, turn the power on.

Turn the ceiling light on and off time and again to ensure that everything works fine.

If you experience any problem, go through the steps and check if you have done something wrong.

Situations Which May Make You Remove Your Ceiling Light Cover

Besides changing the bulb or light cover, there are many more reasons to change the ceiling light cover. We have discussed some of them briefly.

1- Cleaning

As you know, anything that is not touched for a long time gets dirty, and so can the cover of your ceiling light.

Therefore, it’s good to remove and clean the light cover from time to time to look nice. And also, no build-up around the light can lead to any damage to your light fixture.

2- New Ceiling Light

If you aim to install new ceiling lights, you will need to remove the previous one before installing the new one.

We have already discussed the process of doing so in the article. But you need to pay close attention to the wiring of the light, disconnecting the old light and installing the new one.

3- When Renovating

If you are remodeling your room, bathroom or kitchen etc., you will need first to remove the old light cover to gain access to the light.

But be sure to be extra careful and gentle in this step so that you neither damage the wires nor harm yourself.

4- For Replacing The Light/Bulb

Some ceiling lights in the market do not need the entire cover to be removed for changing the bulb.

If you have one of those light models, you will need a long stick to push down the spring clip so that it releases and gets removed. This way, you can replace the old bulb with a new one.

Final thoughts

Removing ceiling light covers is not a big science, and there’s no need to complicate it. You can do it easily through some connected and straightforward steps, including the first preparation step.

The initiative measures are arranging a stool, pliers, and flashlight and switching off the power for safety purposes. A pair of gloves will protect you and help you rotate the cover.

You might have decorative trims around the cover, so make sure to remove them before removing the spring clip with pliers. Now, it’s time to get in action and start removing the glass cover through some tips.

Rotate it first and if it does not remove, bump it with the rubber side of a shoe and take it off. You can further clean or replace the bulb light if you want.

There can be many more reasons for you to remove the ceiling light cover except changing it. It includes cleaning and renovating or, as in most cases, replacing the light.

FAQs

What makes a ceiling light cover good? 

A good ceiling cover is easy to install and remove without any tools. It should also be beautiful enough not to ruin the look of your ceiling light.

What is the benefit of no screw ceiling light cover?

One of the main features of no screw ceiling light cover is that the bulb can be removed or replaced without removing the cover entirely. They are also suitable for added safety so that no one gets an electric shock when handling the cover.

Is it easy to remove a plastic ceiling light cover? 

Yes, it is pretty simple to remove a plastic ceiling light cover. You only need to push down the spring clip, pull it away from the light fixture and keep it aside.
A safety measure to take here is to turn off all the power before this step so that there are no chances of electric shock.

Leave a Comment