How To Remove The Ball Bearing Drawer Slides? (3 Methods)

The drawers and desk drawers are made from metal slides to move the drawer quickly in or out. These slides include either ball bearings or smooth-operation rollers.

The drawer is hard to open, or something falls behind the drawer chamber. The sort of slide your drawer employs will rely on removing an empty drawer using metal slides.

Some slides include two stationary roller tracks on both sides of the drawer. They have a simple design. Other slides are extensions that make it possible to open the drawer further.

These slides are often two halves that are stationary, with a center rail moving along with the drawer.

Method 1: Getting Wood-Glide and Free-Rolling Drawers to Open

remove the ball-bearing drawer slides

Extend the drawer as far as it will allow.

Take a stand in front of the piece of furniture, grab the front panel’s handle or knob, and begin sliding the drawer out till it stops moving.

If there isn’t a stopper on the drawer, it should just pop out. If you run into resistance, you may need to shift the drawer around a bit to get it to open.

  • Most drawers have a stopper to prevent them from falling out by accident. The stopper on free-rolling drawers is usually a little raised lip on the front side of the inside track.
  • Make sure there’s enough room between you and the drawer’s front so it can fully stretch.

Drop down the front of the drawer.

Drill on the drawer side to gently elevate the back end. This makes it possible to pull the drawers out of the rest of the trajectory higher than the stopper at the forefront of the track.

  • You can have to rock the drawer or jostle it to assist loosen the wheels. However, be careful not to go too harsh or harm it or its attachments.

Finish by directly pulling out a drawer.

After you pass the wheels or back edge, you need to move the drawer off the tracks and in the piece of furniture out of the opening. Place the drawer on a level, sturdy surface and continue the operation to obtain additional drawers.

  • If you have problems getting the drawer out, it is likely to be equipped with different stop mechanisms, such as the heels or the stabilizer.

Method 2: Free Metal-Glide Lever Drawer

 remove drawer with metal glides on bottom

Open the drawer and indicate the levers of the track in the exterior walls.

On either side of the drawer, there should be a lever right around the center of the track. Either straight or somewhat bent. Their task is to avoid the drawer being removed until it is decommissioned.

  • Be sure not to pick up your fingertips when you open the door on the overlap tracks.
  • The most frequent straight tabs are full extension diaphragms on 12 in (30 cm) drawers. Typically, three fourth-degree slide paths have curved trace levers, commonly found on 6 in (15 cm) box drawers.

Simultaneously press both levers down.

The best technique to achieve this is to remove the lever with your thumbs and forefingers while holding the drawer with the rest of your fingers from the bottom. You will not drop the drawer in that way if it unforeseen leaves its track.

  • Use the left hand to push the lever on the left side and the right hand to push the lever on the right side of the drawer.
  • Some track levers may require pulling up instead of pulling down. This setup is, however, relatively uncommon.

Pull out the drawer while keeping the levers straight.

Continue to slide the drawer towards you so that both levers remain uncontrolled. It should lift straight out when it reaches the end of its tracks. Remove the following drawers from the piece in the same way.

  • Place the drawer on a flat, solid surface when you are ready to put it down.

Method 3: Unassemble Of Stabilizer Screws Drawers

Run the drawer out and position the stabilizer screws at the end of the channels.

On the bottom of each track, you’ll locate those screws. It is used to secure two halves of the way, which is duplicated to hold the drawer in place as a catch tab.

  • If there are metallic tracks in the drawer, you want to remove but no screws at the end, these might be metal glider drawers with levers. See whether a pair of gauge heavers can be found to push that will allow you to free the drawer.

To remove the stabilizer screws, use the proper screwdriver.

Turn the screws to the left, then pull them free of the trousers in the track hardware. Somewhere you will not lose them, set both screws aside.

  • Most drawers with stabilizer tubes have two (5.1 cm) #8 screws to be removed by the screwdriver Phillips.

Lift the two sections of track on the catch tabs.

Simultaneously pull up both tabs. As you do, from the bottom half, the upper half of the track is taken away, allowing the tractor to open past the stalemate.

  • The catch tabs should contain enough lip for you to grab between your thumb and forefinger effortlessly.

Take the rest of the way out of the drawer.

Guide the drawer off its rails without leaving the catch tabs. Hold it as straight as possible and move it in line with the paths to not stick. Set it carefully and go into the following drawer when it is clear.

  • If you remove several drawers, check the lip of a bit of number on the right side of each drawer. These show where the drawer is going, making it easy for all of them to get back to their proper spot.
  • Work simply the flip side to reinstall a drawer with stabilizer screws. Line the door and the track, lower the fishing tabs and thread the tighteners over the lower part of the track.

Method 4: Anti-Tip Cable Drawers Remove

 remove the ball-bearing drawer

Spread out the drawer and look back for the cable.

Then pull out the drawer and have a look into the rear panel. You should observe a little metal wiring attaching the drawer to the furniture body. This cable is used to restrict the opening of more than one drawer simultaneously.

  • Cable control is a popular safety feature in heavy parts that are likely to lose stability if several open drawers.
  • The cables are connected to special plates on the rear panel on the top and bottom drawers. They are threaded through eyes through the rear of the middle drawers.

Undo the cable-bearing screws.

Depending on how the counter-tip hardware is configured, there maybe 1 or 2 screws, although a pair of screws is most usual. Turn the screws on the left (in the other direction) until they’re loose enough to pull them out by hand.

  • Remove the screws in your pockets or put them on a table nearby or counter to prevent loss.
  • A variety of devices may require various screwdrivers. However, ahead of Phillips should, in most situations, do the trick.Press and hold off the disc lock tabs if your drawer has them.

Review the rear part on either side of the drawer of metal rails. If you can adjust a pair of tabs, press them both in and off to allow the drawers to slide freely.

  • Keep a firm grasp on the drawer sides while taking care of the disconnection tabs.
  • Make sure the two accounts are fully pushed in. They may not “lock” on their own, which implies that you must press on them until removing the drawer.

Slide the drawer off its tracks straight away.

Pull the drawer in the direction of you until the piece of furniture comes off. You might need to slightly lift or slant the drawer upwards to clear the end of the paths.

  • Before removing the following tractor or continuing through your business, do not forget to press the expanded metal tracks into the piece back.

Conclusion
No matter what type of drawer slide you have on your furniture, removing the drawers can be a straightforward operation if you do some study before you start.

You have to determine the types of drawer paths you use and follow the step-by-step instructions to do this simply and quickly.

Always start with the top drawer and work your way down to prevent the part from taping when removing several drawers from the piece of furniture.

The drawer’s content is drawn before it is pulled out, making it easier to grab on and manoeuvre. If you drop it, it will also lower your risk of injury.

1 thought on “How To Remove The Ball Bearing Drawer Slides? (3 Methods)”

Leave a Comment